Adapters, Cables, & Connectors

⬇︎ Full List of Specs and Features Below ⬇︎ Don't buy more than you need. Why buy a large bulk pack when you only need a few? Save money...

⬇︎ Full List of Specs and Features Below ⬇︎ Don't buy more than you need. Why buy a large bulk pack when you only need a few? Save money a...

⬇︎ Full List of Specs and Features Below ⬇︎ Don't buy more than you need! Save money and buy exactly the amount for your project. 14 Gaug...

⬇︎ Full List of Specs and Features Below ⬇︎   Use this adapter to change your MBoards Battery from an XT60 connector to an XT90 connector. Sim...

Use this adapter to convert your FOCBOX Unity/Tenka's stock Female XT90 to a Male XT60.  Sold Individually. 

⬇︎ Full List of Specs and Features Below ⬇︎ Simple adapter to make parallel connections easy and clean. No cable management to worry about. Sm...

⬇︎ Full List of Specs and Features Below ⬇︎ Simple adapter to make series connections easy and clean. No cable management to worry about. Smal...

Used to connect 2 VESC® based ESCs to 1 Battery. Simply plug in each VESC® based ESC to each of the female XT60 connectors and plug the battery i...

⬇︎ Full List of Specs and Features Below ⬇︎ A simple extension cable to help you on your build. Features 1 female connector and 1 male connect...

⬇︎ Full List of Specs and Features Below ⬇︎ Simple adapter to make parallel connections easy and clean. No cable management to worry about. Sm...

⬇︎ Full List of Specs and Features Below ⬇︎ Simple adapter to make series connections easy and clean. No cable management to worry about. Smal...

Use this adapter to plug your motors with 4mm bullet connectors into a FOCBOX Unity/Tenka.  Cable Length: 1.5in  |  38mmCable AWG: 12AWG Sold as a...

⬇︎ Full List of Specs and Features Below ⬇︎ Female MR30 to Female 4mm Bullet connector adapter. Used to adapt the Hobbywing ESC to other motors....

⬇︎ Full List of Specs and Features Below ⬇︎ Male MR30 to Male 4mm Bullet connector adapter. Used to adapt Direct Drive connections to regular ES...

Use these adapters to connect your motor with 5.5mm bullet connectors to your ESC with 4mm bullet connectors. Sold as pack of 6. 

A simple cable to connect your motor's sensor wire into a Vesc.  Convert 1.5mm JST to 2.0 JST Cable Length: 100mm-110mm 

Use this cable to extend your 6 pin hall sensor wires. Input: JST PH 2.0mm 6 Pin Output: JST PH 2.0mm 6 Pin Cable Length: 200mm 26awg

Use this cable to adapt a 6 pin motor hall sensor wire to a 5 pin sensor port.  Input: JST PH 2.0mm 6 Pin Output: JST PH 2.0mm 5 Pin Cable Length...

Use this cable to extend your 5 pin hall sensor wires. Input: JST PH 2.0mm 5 Pin Output: JST PH 2.0mm 5 Pin Cable Length: 200mm 26awg

Use this cable to adapt a 5 pin motor hall sensor wire to a 6 pin sensor port.  Input: JST PH 2.0mm 5 Pin Output: JST PH 2.0mm 6 Pin Cable Length...

⬇︎ Full List of Specs and Features Below ⬇︎ Used to connect 2 FSESC ESCs together.  What's In The Box?- (1) Canbus Connection Cable

⬇︎ Full List of Specs and Features Below ⬇︎ This cable connects your Controller receiver to your VESC. It's usually always an after thought wh...

⬇︎ Full List of Specs and Features Below ⬇︎ Building a dual motor electric skateboard? This servo Y-cable allows you to drive two VESCs or ESC...

2 Pin JST 2.0 connector to raw leads.  26awg Wire. Approximately 120mm in length. Compatible with:Battery Percentage IndicatorFocBox 2 Pin Port Us...

Supports Charging (Phone, Remote, etc.)Supports Data Transfer (Programing Vescs)3 Foot Cable Length

Supports Charging (Phone, Remote, etc.)Supports Data Transfer (Programing Vescs)3 Foot Cable Length

⬇︎ Full List of Specs and Features Below ⬇︎ Whether it's a replacement charge port for your MBoards battery or a charge port for a DIY project...

*PLEASE NOTE* This is a replacement power switch that is compatible with the following ESCs: Single Belt ESCDual Belt ESCDual Hub ESC This Power Bu...

⬇︎ Full List of Specs and Features Below ⬇︎ Finally a solid App for DIY Electric Skateboards. Log rides, create different ride modes, track y...

Sold Individually.  Use this adapter to convert your Battery's XT90 connector to match your ESC's XT60 connector. 

TPU Cable Brackets to keep the inside of your enclosure nice and neat. The neater your set up, the cooler your board will run.  Included: (3) Large...

Panel Mountable XT90 for battery box builds. Included:(1) XT90e-m(1) Female XT90(1) End Cap(2) M4 Screws(2) M4 Nylon Nuts *Slightly oversized hardw...

Use this cable to connect your external battery box to your ESC.  Length: 17.5in (44.5cm)Wire: 10awg